The short answer
Expect to pay around £80 per hour for standard work, £600 a day and £120 per hour for out‑of‑hours emergencies (one‑hour minimum).
We recommend confirming the written scope before work begins so you can compare hourly rates and emergency pricing accurately.
| Service | Price |
|---|---|
| Standard labour | £80 per hour |
| Day rate | £600 |
| Emergency labour | £120 per hour |
| Fault finding | £80 per hour |
| EICR, up to three beds | £150–£250 |
These figures include VAT, parts, labour, testing and certification where applicable. Most faults are traced within one to two hours, but safe isolation and testing must never be rushed. Check service guarantees and customer reviews, and make sure your electrician explains any remedial work and provides a written estimate before proceeding.
What changes the price
The final cost depends on the fault or installation scope, access, property age and whether work is needed during normal hours. We assess the circuit condition, required testing and certification before giving you a fixed written price.
-
Fault complexity: Intermittent faults, damaged cables or obsolete VIR, rubber or aluminium wiring can require longer diagnostic testing and safe isolation.
-
Access difficulty: Restricted voids, high-level fittings, concealed routes and listed-building constraints may increase labour time or require specialist methods.
-
Service urgency: Our standard-hours rate differs from out-of-hours attendance, particularly where immediate action is needed to make an installation safe.
Material quality also affects the total: compliant accessories, cable, protective devices and fire-rated fittings vary in cost. Electrician experience matters too; competent diagnosis reduces unnecessary disturbance and guarantees work meets BS 7671 requirements.
Cost by property size
Property size affects electrical costs because larger homes usually have more circuits, accessories and cable routes to inspect, test or alter. We assess bedroom count and floor area alongside the consumer unit’s condition, accessibility and the age of wiring. A compact flat may need fewer test points than a detached house, while extensions, lofts and outbuildings increase labour time.
| Property size | Typical scope factor | Likely time |
|---|---|---|
| 1–2 bedrooms | Fewer circuits, shorter runs | Half to one day |
| 3 bedrooms | Standard domestic distribution | One to two days |
| 4+ bedrooms | More circuits and routes | Two days or more |
We’ll allow sufficient time for safe isolation, inspection and verification; larger layouts shouldn’t be priced solely by room numbers. In Canterbury’s older properties, concealed cable routes and legacy wiring can further affect duration.
What is included and what is not
Our written fixed-price quote sets out what is included before work begins, for example labour, the specific materials we have agreed to supply, testing, certification and VAT. We specify the circuit work, accessories, protective devices and any certification we will provide, so you can check that the materials included match the agreed scope. Where applicable, we will supply electrical installation certificates, minor works certificates or EICR documentation as stated in the quote.
We also set out exclusions. “Travel excluded” means attendance beyond our stated service area, parking, congestion charges or unusual access costs may be charged separately and will be agreed before booking. Hidden defects, unsafe existing wiring, asbestos surveys, plastering, decorating, builder’s works and work required from the network operator are not included unless listed in the quote. If testing reveals VIR, rubber or aluminium cabling that requires additional remedial work, we will explain the safety issue and provide a revised written price; we will not proceed without your written approval.
Note on legal duties: contrary to some beliefs, contractors do not have an automatic duty to carry out work beyond what is specified in a written quote; their legal obligation is to perform the work agreed in the contract and to comply with applicable safety and regulatory standards.
How Canterbury compares with the national average
In Canterbury and Harbledown, Rough Common and Wincheap we work across Georgian brick houses near the cathedral precincts, Victorian terraces in Wincheap and St Dunstan's, large student rental stock, new estates at the edges. The recurring themes are student and rental HMO compliance, listed and period property in the precincts, commercial work for the city centre; we explain what we find in plain English and put a fixed price in writing before any work begins.
When you would pay more, and why
You’ll usually pay more where work involves out-of-hours attendance, difficult fault-finding, restricted access or additional testing and certification. Emergency call-outs require rapid mobilisation and may fall outside normal working hours, so our out-of-hours rate reflects that response. Faults that are intermittent, concealed or associated with older VIR, rubber or aluminium wiring can take longer to trace safely.
Costs can also rise when we need to isolate circuits, work in confined roof spaces, protect listed-property fabric, or use specialist equipment for testing, locating cables or verifying earth-fault performance. Peak demand can affect appointment availability, particularly during severe weather or after flooding, when safe inspection is essential before circuits are re-energised. Remedial work identified during an EICR, such as replacing damaged accessories or correcting unsafe connections, is priced separately because the scope cannot be confirmed until testing is complete.
Is it worth it?
Whether electrical work is worth the cost depends on the risk it removes and the reliability it restores. We recommend weighing the price against the condition of the installation, not simply the inconvenience of a fault. Damaged insulation, overheating connections, obsolete wiring and repeated tripping can compromise safety and require proper diagnosis.
A qualified electrician can identify defects that aren’t visible at the socket or consumer unit; correcting them promptly may prevent damage to appliances, reduce the chance of fire or electric shock, and avoid more extensive remedial work later.
For landlords, it is a legal requirement in England for periodic electrical safety inspections and remedial work to meet the standards set out in the Electrical Safety Standards in the Private Rented Sector (England) Regulations 2020; in other parts of the UK, similar duties may apply under local legislation so landlords should check the applicable rules. For homeowners there is no general legal obligation to carry out electrical work, but documented work and appropriate certification (for example, an Electrical Installation Condition Report or Building Regulations compliance when required) can be valuable for safety assurance and may assist with future alterations or sale.
The value of timely electrical work is reassurance, more dependable operation and potential long‑term savings from addressing faults before they worsen.
Related guides
For further guidance, see our practical guides on EICRs, consumer-unit upgrades, rewiring older Canterbury properties, EV chargepoints and electrical emergencies. They explain when inspection, testing and certification are needed, and what competent electrical work should include.
Our EICR guide covers report observations, remedial priorities and landlord duties. The consumer-unit guide addresses circuit protection, RCD coverage and installation certification. For Historic rewiring, we outline precautions for Victorian properties, including VIR or rubber-insulated cable, concealed routes and listed-building considerations.
Our EV guide explains load assessment, dedicated circuits, earthing arrangements and Chargepoint grants. Before selecting a chargepoint, we’ll help you understand whether your existing supply and consumer unit are suitable. The emergency guide covers immediate isolation steps where there is burning, damage, water ingress or repeated tripping, and when you shouldn’t reset a protective device.